科尔摩根 S70602-PBNANA 伺服驱动器

科尔摩根 S70602-PBNANA 伺服驱动器

科尔摩根 S70602-PBNANA 伺服驱动器

S70602-NANANA由科尔莫根制造，是其S700伺服驱动系列的一部分。这些驱动器的特点是S1操作的额定线路功率为4.5千伏安，峰值输出电流为18安均方根值。此外，额定电压为208-480伏，最大DC总线链路电压为900伏

这S70602-NANANA额定电流为6安，额定电压为208-480伏。这个伺服放大器没有扩展卡在插槽1-3中，并且具有没有固件选项。它附带以太猫和车载CANopen。该伺服放大器的外壳尺寸为 70 mm，板载RS232和24V脉冲方向接口。这S70602-NANANA具有不同的集成安全功能，包括安全扭矩关闭(STO)、过压检测、断相监控和短路保护。该放大器还为电机提供温度监控。这S70602-NANANA辅助电源输出为24伏DC和最大噪声发射58分贝。

该伺服放大器的推荐工作温度介于0℃至40℃在额定条件下，最高工作温度为55摄氏度带功率降额2.5%/\u C。最大允许相对湿度为85%无冷凝。这个放大器有一个3M1类振动符合IEC 60529并且具有外壳保护IP 20。保护壳提供基本防尘保护，因此S70602-NANANA必须在没有水或灰尘的地方使用。该伺服放大器符合污染等级2按照国际电工委员会60664-1。建议将该伺服驱动器安装在竖直位置有足够的通风空间。

科尔摩根 S70602-PBNANA 伺服驱动器

The S70602-NANANA is manufactured by Kermogan as part of its S700 servo drive family. These drivers feature a rated line power of 4.5 kVA for S1 operation and a peak output current of 18 A RMS value. In addition, the voltage rating is 208-480 volts, and the maximum DC bus link voltage is 900 volts

This S70602-NANANA is rated for 6 amps and 208-480 volts. This servo amplifier has no expansion card in slots 1-3 and has no firmware option. It comes with Ether Cat and onboard CANopen. The servo amplifier has a housing size of 70 mm with on-board RS232 and 24V pulse direction interfaces. The S70602-NANANA has different integrated safety features, including safety Torque Off (STO), overvoltage detection, phase break monitoring and short circuit protection. The amplifier also provides temperature monitoring for the motor. This S70602-NANANA auxiliary power supply has a 24 volt DC output and a maximum noise emission of 58 dB.

The recommended operating temperature of the servo amplifier is between 0 ° C and 40 ° C under rated conditions, with a maximum operating temperature of 55 ° C with a power derating of 2.5%/\u ° C. The maximum allowable relative humidity is 85% without condensation. This amplifier has a class 3M1 vibration compliant with IEC 60529 and has a housing to protect IP 20. The protective housing provides basic dust protection, so the S70602-NANANA must be used where there is no water or dust. The servo amplifier complies with contamination Class 2 in accordance with International Electrotechnical Commission 60664-1. It is recommended to install the servo driver in a vertical position with sufficient ventilation space.