IC695PNC001AF 用于将RX3i系统连接到PROFINET网络

IC695PNC001AF 用于将RX3i系统连接到PROFINET网络

该IC695PNC001是由艾默生自动化（前身为 GE 智能平台 （GE IP））制造的 PACSystems RX3i 通信模块。该模块是PROFINET控制器模块，用于将RX3i系统连接到PROFINET网络。它支持 PROFINET 2.2 版通用 A 类 IO 控制器，并与 CPU315 或 CPU320 兼容，固件版本为 7.0 或更高版本。每个 PROFINET 控制器最多支持 64 个设备，每个网络最多可连接 8 个 I/O 控制器。此 PROFINET 控制器最多可连接 2048 个 I/O 设备或每个网络 128 个。该模块具有两个 RJ-45 和两个 SFP 插槽以及一个微型 USB 连接器。

IC695PNC001控制器是指按照预定顺序改变主电路或控制电路的接线和改变电路中电阻值来控制电动机的启动、调速、制动和反向的主令装置。

控制器由程序计数器、指令寄存器、指令译码器、时序产生器和操作控制器组成，它是发布命令的"决策机构"，即完成协调和指挥整个计算机系统的操作。

IC695PNC001是PROFINET控制器模块。该模块以前由 GE 智能平台 （GE IP） 制造，现在由 Emerson Automation 制造。该PROFINET控制器使RX3i CPU能够通过PROFINET网络发送和接收数据。

该IC695PNC001兼容固件版本为 7.0 或更高版本的 PACSystem RX3i CPU315 或 CPU320。该模块带有两 （2） 个 RJ-45 和两 （2） 个 SFP 插槽，带有单独出售的 SFP 连接器。仅为这些 PROFINET 端口分配一个 IP 地址。单个 CPU 最多可以安装四 （4） 个IC695PNC001，并且必须仅位于 CPU 所在的主机架上。最多可将六十四 （64） 个 I/O 设备连接到一 （1） 个控制器;每个网络 128 个 I/O 设备，分布在八 （8） 个 I/O 控制器中。此外，单个网络中最多可以安装八 （8） 个 I/O 设备。该模块具有 1 ms、2 ms、4 ms、8 ms、16 ms、32 ms、64 ms、128 ms、256 ms 和 512 ms 的可配置数据更新时间IC695PNC001。

IC695PNC001AF 用于将RX3i系统连接到PROFINET网络

The IC695PNC001 is a PACSystems RX3i communication module manufactured by Emerson Automation (formerly GE Intelligent Platform (GE IP)). This module is the PROFINET controller module for connecting the RX3i system to the PROFINET network. It supports PROFINET version 2.2 General Purpose Class A IO controllers and is compatible with CPU315 or CPU320 with firmware version 7.0 or higher. Each PROFINET controller supports up to 64 devices and up to 8 I/O controllers can be connected to each network. This PROFINET controller can connect up to 2048 I/O devices or 128 per network. The module has two RJ-45s and two SFP slots as well as a micro-USB connector.

IC695PNC001 controller refers to the master device that changes the wiring of the main circuit or control circuit and changes the resistance value in the circuit to control the start, speed regulation, braking and reverse of the motor in accordance with the predetermined sequence.

The controller is composed of program counter, instruction register, instruction decoder, timing generator and operation controller. It is a "decision mechanism" that issues commands, that is, to complete the coordination and command of the operation of the whole computer system.

IC695PNC001 is a PROFINET controller module. The module was previously manufactured by GE Intelligence Platform (GE IP) and is now manufactured by Emerson Automation. The PROFINET controller enables the RX3i CPU to send and receive data over the PROFINET network.

The IC695PNC001 is compatible with firmware version 7.0 or later PACSystem RX3i CPU315 or CPU320. The module comes with two (2) RJ-45s and two (2) SFP slots with separately sold SFP connectors. Only one IP address is assigned to these PROFINET ports. A single CPU can install up to four (4) IC695PNC001s and must be located only on the host shelf where the CPU is located. Up to sixty-four (64) I/O devices can be connected to one (1) controller; There are 128 I/O devices per network, distributed among eight (8) I/O controllers. In addition, up to eight (8) I/O devices can be installed in a single network. The module has configurable data update times IC695PNC001 for 1 ms, 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms and 512 ms.

It occupies A single slot in the chassis and consumes 0.5 A when no SFP device is installed, and A maximum of 1.2 A when two (2) SFP devices are installed, of which the SFP device uses 0.35 A. At 5.5 VDC, the module consumes A maximum of 1.5 A.