A06B-6121-H030#H550伺服放大器模块

AO6B6121H030#H550的特性

CNC Fanuc伺服放大器A06B6121H030#H550模块是一个三相40OCAC至48OVAC主电源装置。ai SPM-30HVI的额定输出为170A，与ail 6OHV电机一起工作。适用于本装置的CNC为16-B、18-B、21i-B、Oi-B/C/D和30/31i/32i。AO6B6121HO30#H550的速度控制范围是速度比1:100.速度变化率等于或小于最大速度的0.1%。它具有-15%至+10%的允许电压偏差。A06B6121H030#H550 ai SPM-30HVI的电源频率为50/60Hz,1Hz。该装置应在0至55°c的环境温度下运行。装置运行的湿度应在90%RH或以下，振动应低于0.5G。安装应在磁柜中进行。

ci SPM-30HVI装置的优点

Fanuc伺服放大器AO6B6121H030#H550 ci SPM-30HVI必须安装在一个密封的机柜中，以满足运行时环境温度为0至55°℃，储存或运输时环境温度为-20至60C的环境要求。其他需要注意的环境条件包括湿度(相对湿度应为90%或更低]和无冷凝。运行时，振动应保持在0.5G以下。为避免损坏，设备应无异物或腐蚀性材料。应远离水滴和水雾。

为了防l止HFanuc伺服放大器A06B6121H030#H550 ai SPM-30HVI单元后面的热星积骤并造成损坏，应采取适当的措施。安装应在磁柜中，该磁柜的后部有一个散热器。散热器散发半导体产生的热量。

A06B-6121-H030#H550伺服放大器模块

Characteristics of AO6B6121H030#H550

CNC Fanuc Servo Amplifier A06B6121H030#H550 module is a three-phase 40OCAC to 48OVAC main power supply unit. The ai SPM-30HVI has a rated output of 170A and works with ail 6OHV motors. The CNC for this device is 16-B, 18-B, 21i-B, Oi-B/C/D and 30/31i/32i. The AO6B6121HO30#H550 speed control range is speed ratio 1:100. The rate of change of velocity is equal to or less than 0.1% of the maximum velocity. It has an allowable voltage deviation of -15% to +10%. A06B6121H030#H550 ai SPM-30HVI has a power supply frequency of 50/60Hz,1Hz. The unit shall operate at an ambient temperature of 0 to 55°c. The operating humidity of the device should be 90%RH or less, and the vibration should be less than 0.5G. Installation should be carried out in a magnetic cabinet.

Benefits of the ci SPM-30HVI device

The Fanuc servo amplifier AO6B6121H030# H550ci SPM-30HVI must be installed in a sealed cabinet to meet the environmental requirements of 0 to 55° C for operation and -20 to 60 ° C for storage or transport. Other environmental conditions to be aware of include humidity (relative humidity should be 90% or less) and no condensation. When running, the vibration should be kept below 0.5G. To avoid damage, the equipment should be free of foreign bodies or corrosive materials. Keep away from water droplets and mist.

In order to prevent the hot star buildup behind the HFanuc servo amplifier A06B6121H030#H550 ai SPM-30HVI unit and cause damage, appropriate measures should be taken. The installation shall be in a magnetic cabinet with a radiator at the rear of the cabinet. Radiators dissipate heat generated by semiconductors.