GE DS200SDCIG1AEB  应用于模拟量驱动控制卡

GE DS200SDCIG1AEB  应用于模拟量驱动控制卡

产品描述

GE DC 电源和仪表板DS200SDCIG1AEB用作 DC2000 驱动器的接口。DS200SDCIG1AEB装有 5 个保险丝，用于保护电路板免受损坏。如果发生电源过载情况，保险丝可能会熔断以保护组件免受损坏。一个有价值的功能是，如果保险丝熔断，您可以检查电路板上的 LED 灯并确认电路板是否出现问题。您可以参考电路板附带的信息，并确定保险丝熔断的可能原因。

您可能确定必须立即更换主板，或者确定驱动器中的某种状况导致主板出现故障。如果是这种情况，请先更正驱动器中的状况。例如，暂时过载情况导致保险丝熔断。在这种情况下，如果暂时过载情况不太可能再次发生，只需从驱动器上卸下电路板，更换保险丝，重新安装电路板，然后继续制造过程。

您必须只允许合格的维修人员检查、修理或以其他方式触摸DS200SDCIG1AEB板或安装它的驱动器。这也适用于更换熔断的保险丝。维修人员必须熟悉制造现场的设备，尤其是驱动器和电路板。不合格的维修人员可能会损坏组件或将组件暴露在危险的高电压下tage.不合格的服务人员可能会受到高压电流的伤害。

GE DS200SDCIG1AEB  应用于模拟量驱动控制卡

Product description

The GE DC power supply and dashboard DS200SDCIG1AEB serve as the interface for the DC2000 driver. The DS200SDCIG1AEB is equipped with 5 fuses to protect the board from damage. In the event of power overload, fuses may blow to protect components from damage. A valuable feature is that if a fuse blows, you can check the LED lights on the board and confirm if there is a problem with the board. You can refer to the information that comes with the circuit board and determine the possible cause of a blown fuse.

You may determine that the motherboard must be replaced immediately, or that something in the drive is causing the motherboard to fail. If this is the case, correct the condition in the drive first. For example, a temporary overload situation can lead to a blown fuse. In this case, if the temporary overload situation is unlikely to occur again, simply remove the board from the drive, replace the fuse, reinstall the board, and continue the manufacturing process.

You must only allow qualified service personnel to inspect, repair or otherwise touch the DS200SDCIG1AEB board or the drive on which it is mounted. This also applies to replacing blown fuses. Maintenance personnel must be familiar with the equipment at the manufacturing site, especially the drives and circuit boards. Unqualified maintenance personnel may damage the component or expose the component to dangerously high voltage tage. Unqualified service personnel may be harmed by high voltage current.

GE DS200SDCIG1AEB  应用于模拟量驱动控制卡

GE DS3800DFXA1B1C GE Fanuc 控制器 GE DS3800HAIA1D1B

GE DS3800DFPF1B1C GE Fanuc 控制器 GE DS3800HAFA1E1FE

GE DS3800DFPF GE Fanuc 控制器 GE DS3800HAFA1D1E

GE DS3800DFEB1C1B GE Fanuc 控制器 GE DS3800HAFA1B1D

GE DS3800DFCD1B1B GE Fanuc 控制器 GE DS3800HADA1B1B

GE DS3800DEPB1A1B GE Fanuc 控制器 GE DS3800HADA1A1A

GE DS3800DEPB1A1A GE Fanuc 控制器 GE DS3800HADA

GE DS3800DEPB1A GE Fanuc 控制器 GE DS3800HACB1A1B

GE DS3800DEPB GE Fanuc 控制器 GE DS3800HACB

GE DS3800DDIBIB1C GE Fanuc 控制器 GE DS3800HACA1A1A

GE DS3800DDIB1B1C GE Fanuc 控制器 GE DS3800HACA