IS200DTAIH1ABB 一款单工模拟输入/输出终端板

IS200DTAIH1ABB 一款单工模拟输入/输出终端板

IS200DTAIH1ABB 一款单工模拟输入/输出终端板

产品描述

IS200DTAIH1ABB是为Mark VI系统创建的GE组件。Mark VI是以Speedtronic系列名称发布的燃气/蒸汽轮机管理系统。自 1960 年代以来，该系列在其各种迭代中一直用于涡轮机管理。Mark VI具有以太网通信功能，并在硬件和软件中包括板载诊断（极限检查）。

IS200DTAIH1ABB是单工模拟输入/输出端子板。它是用于模拟信号的紧凑型输入板。该板安装在塑料支架中，允许PCB安装在DIN导轨上。该板有十个模拟输入和两个模拟输出。输出为 0-20mA，但可通过重新配置跳线将输出配置为 0-200mA 电流。

IS200DTAIH1ABB有一个带闭锁紧固件的 37 针连接器。这被标记为JR1。该板有一个带有 1 个螺钉连接的端子板 （TB48）。该端子条永久安装在电路板上。#18 AWG 屏蔽双绞线通常用于接线端子。请注意，螺钉 43/44 被指定为接地 （SCOM） 连接。地线应尽可能短。该板有 1 个跳线开关;这些标记为JP10A / B-JP20A / B （0）加上JP<>。该板还包括各种电容器、电阻器和集成电路，以及四个小子面板。电路板上的跳线用于配置电流和电压。

GE为IS200DTAIH1ABB提供了技术支持。有关此 PCB、其组件或安装程序的信息可通过手册、用户指南和数据表找到。

IS200DTAIH1ABB 一款单工模拟输入/输出终端板

Product description

The IS200DTAIH1ABB is a GE component created for the Mark VI system. The Mark VI is a gas/steam turbine management system released under the Speedtronic family name. The series has been used for turbine management in its various iterations since the 1960s. The Mark VI has Ethernet communication capabilities and includes onboard diagnostics (limit checks) in both hardware and software.

The IS200DTAIH1ABB is a simplex analog input/output terminal board. It is a compact input board for analog signals. The board is mounted in a plastic bracket that allows the PCB to be mounted on the DIN rail. The board has ten analog inputs and two analog outputs. The output is 0-20mA, but the output can be configured to 0-200mA current by reconfiguring the jumper.

The IS200DTAIH1ABB has a 37-pin connector with a locking fastener. This is labeled JR1. The board has a terminal board (TB48) with 1 screw connection. The terminal bar is permanently installed on the circuit board. #18 AWG shielded twisted pair cables are commonly used for terminal use. Note that screws 43/44 are designated for ground (SCOM) connections. Ground cables should be as short as possible. The board has a jumper switch; These are labeled JP10A/B-JP20A/B (0) plus JP<>. The board also includes a variety of capacitors, resistors, and integrated circuits, as well as four small panels. Jumpers on the board are used to configure current and voltage.

GE provides technical support for the IS200DTAIH1ABB. Information about this PCB, its components, or installer can be found in manuals, user guides, and data sheets.