2711-T10C10 是一款 PanelView 1000 标准操作终端

Allen-Bradley 2711-T10C10 终端是 PanelView 标准 1000 人机界面终端系列中的一款触摸屏人机界面终端。该界面配有 10 英寸彩色显示屏，由于其分辨率为 640 x 480 像素，可帮助操作员更好地可视化应用过程。屏幕是彩色有源矩阵类型的屏幕。Allen-Bradley 2711-T10C10 人机界面终端可以在相对湿度范围为 5% 至 95% 的环境中运行而不会带来任何不便，不会有冷凝水，最高额定温度为 50 摄氏度，最高海拔为 2000 米。它被设计为在室内环境中运行，因为必须保护屏幕免受来自阳光直射的紫外线的影响。需要在执行手册中的每个步骤以及从所有连接的设备断开电源后安装此接口。Allen-Bradley 2711-T10C10人机界面终端的显示面积为211×158毫米，整体宽度为370毫米，高度为282毫米，长度为112毫米。它的重量为 7 磅。该接口终端提供的通信机制是具有自己的打印机端口的 DeviceNet 端口。它还具有 1008 KB 的通用内存和 310 KB 的闪存。

Allen-Bradley 2711-T10C10 是一种人机界面 （HMI） 设备，有时也称为人机界面 （MMI）。该设备是 Allen-Bradley 的 PanelView Standard 1000 操作终端的一部分，该终端具有 10 英寸彩色有源矩阵 TFT 屏幕、DeviceNet 通信接口和触摸屏操作员输入。

2711-T10C10 通常是一种嵌入式安装设备，安装在外壳上，其防护等级相当于 NEMA Type 12、13、4X（仅限室内使用）、IEC IP54 和 IP65 标准。该外壳必须配备一个面板切口，该开口符合正确安装 HMI 设备所需的开口。此外，外壳必须具有平坦光滑的表面，振动和冲击限制在 29 至 2000 赫兹和 15 克以内。

2711-T10C10 还支持通过嵌入式 RS-232 打印机端口与报警打印机直接通信。此打印机端口可以配置为以特定和定义的时间间隔打印警报和事件记录，以便存档和报告。RS-232 打印机端口具有 1200、2400、9600 和 19,200 Kbps 的可选波特率配置。

该操作终端还配备了 1008 KB 非易失性存储器和 310 KB 随机存取存储器 （RAM）。可选的 ATA 存储卡可以安装在 2711-T10C10 上，以补充嵌入式非易失性存储器。

要操作此操作终端，外部电源电压必须沿 85-264 赫兹的频率范围连接到该设备的电源输入端，交流电压范围为 47-63 伏。它的功耗为 55 伏安。

2711-T10C10 是一款 PanelView 1000 标准操作终端

The Allen-Bradley 2711-T10C10 terminal is a touch screen HMI terminal in the PanelView Standard 1000 HMI terminal series. The interface features a 10-inch color display that helps operators better visualize the application process thanks to its 640 x 480 pixel resolution. The screen is a color active matrix type screen. The Allen-Bradley 2711-T10C10 HMI terminal can operate without inconvenience in the relative humidity range of 5% to 95%, without condensation, with a maximum rated temperature of 50 degrees Celsius and a maximum altitude of 2000 meters. It is designed to operate in an indoor environment, as the screen must be protected from ultraviolet rays from direct sunlight. This interface needs to be installed after performing each step in the manual and after disconnecting power from all connected devices. The Allen-Bradley 2711-T10C10 HMI terminal has a display area of 211×158 mm, an overall width of 370 mm, a height of 282 mm, and a length of 112 mm. It weighs 7 pounds. The communication mechanism provided by this interface terminal is a DeviceNet port with its own printer port. It also has 1008 KB of general purpose memory and 310 KB of flash memory.

The Allen-Bradley 2711-T10C10 is a human machine interface (HMI) device, sometimes referred to as Human Machine Interface (MMI). The device is part of Allen-Bradley's PanelView Standard 1000 operating terminal, which features a 10-inch color active Matrix TFT screen, DeviceNet communication interface, and touch screen operator input.

The 2711-T10C10 is typically a recessed mounting device, mounted on a housing with a protection rating equivalent to NEMA Type 12, 13, 4X (for indoor use only), IEC IP54 and IP65 standards. The housing must be equipped with a panel notch that meets the opening required for proper installation of the HMI device. In addition, the housing must have a flat, smooth surface with vibration and shock limited to 29 to 2000 Hz and 15 grams.

The 2711-T10C10 also supports direct communication with the alarm printer via an embedded RS-232 printer port. This printer port can be configured to print alert and event records at specific and defined intervals for archiving and reporting. The RS-232 printer port has optional baud rate configurations of 1200, 2400, 9600, and 19,200 Kbps.

The operating terminal is also equipped with 1008 KB of non-volatile memory and 310 KB of random access memory (RAM). An optional ATA memory card can be installed on the 2711-T10C10 to complement the embedded non-volatile memory.

To operate this operating terminal, the external power supply voltage must be connected to the power input of the device along a frequency range of 85-264 Hz, with an AC voltage range of 47-63 volts. It has a power consumption of 55 volt-amps.