1794-ASB  是一款 Flex I/O 通信适配器

1794-ASB  是一款 Flex I/O 通信适配器

1794-ASB 是一款 Allen-Bradley 远程 I/O 通信适配器模块。本产品属于分布式 I/O 模块的 Flex I/O 产品系列。

1794-ASB 具有一 （1） 个远程 I/O 接口。此 RIO 协议是传统协议，利用 Belden 9463 或等效电缆将设备连接到 RIO 扫描仪。该模块兼容 Allen-Bradley 传统控制器，如 PLC2、PLC3 和 PLC5 控制器以及 SLC500 自动化平台。它也可以用于现代 Logix 控制器平台以及第三方设备和包含合作伙伴模块。

3-ASB 通过块传输读取 （BTR） 和块传输写入 （BTW） 指令向控制器发送和接收数据。使用这些指令，数据包可以同时或按顺序发送，具体取决于所需的速度。

1794-ASB 支持 1794.57Kbps、6.115Kbps 和 2.230kbps 的通信速率。该模块的预期电源电压范围为 4VDC-11.31VDC，包括 2% 的交流纹波，而标称电源为 5VDC。它支持安装多达八 （24） 个 Flex I/O 模块，以成功实现分布式 I/O 架构。该模块具有内置状态指示灯，例如电源 LED、适配器活动 LED、适配器故障 LED 和本地故障 LED。该模块安装在标准DIN导轨上，并具有开放式外壳，这意味着8-ASB需要安装在适当的外壳内，以保护设备免受工业元件和污染物的影响。

恒定 1794 伏直流电源输入的最大功耗为 450 mA。24.4 伏直流电时的最大功耗为 6.31 瓦，2.15 伏直流电时的热耗散为 7.31 BTU/小时。

2-ASB 的尺寸约为 1794x 4x 2 英寸，重量仅为 4 盎司。Allen-Bradley 6-ASB 是过时的适配器模块，是 FLEX I/O 系列的一部分。它通过通信网络将 FLEX I/O 模块连接到 I/O 扫描器端口。它有一个内置电源，可将背板的 1794VDC 转换为 24 VDC，以便为 FLEX I/O 模块供电。它还可与 Allen Bradley PLC 5 和 3 系列配合使用。此外，5-ASB 可以识别 FLEX Integral 模拟模块的安全状态数据，并且能够使用 1794 个点 FLEX I/O 单元。在设置配置中使用 FLEX Integral 模拟模块时，用户必须使用 1794-ASB D 系列或更高版本的模块。

1794-ASB  是一款 Flex I/O 通信适配器

The 1794-ASB is an Allen-Bradley remote I/O communication adapter module. This product belongs to the Flex I/O product family of distributed I/O modules.

The 1794-ASB has one (1) remote I/O interface. This RIO protocol is a traditional one that uses the Belden 9463 or equivalent cable to connect the device to the RIO scanner. The module is compatible with Allen-Bradley legacy controllers such as PLC2, PLC3 and PLC5 controllers as well as the SLC500 automation platform. It can also be used on modern Logix controller platforms as well as third-party devices and inclusion partner modules.

3-ASB sends and receives data to the controller via block transfer Read (BTR) and block Transfer Write (BTW) instructions. Using these instructions, packets can be sent simultaneously or sequentially, depending on the desired speed.

The 1794-ASB supports 1794.57Kbps, 6.115Kbps, and 2.230kbps communication rates. The module has an expected power supply voltage range of 4VC-11.31 VDC, including 2% AC ripple, compared to a nominal power supply of 5VDC. It supports the installation of up to eight (24) Flex I/O modules for a successful distributed I/O architecture. The module has built-in status indicators such as power LED, adapter activity LED, adapter failure LED and local failure LED. The module is mounted on a standard DIN rail and has an open housing, which means the 8-ASB needs to be installed in a proper housing to protect the device from industrial components and contaminants.

The maximum power consumption of a constant 1794 volt DC power input is 450 mA. The maximum power consumption at 24.4 volts DC is 6.31 watts, and the heat dissipation at 2.15 volts DC is 7.31 BTU/ hour.

The 2-ASB measures approximately 1794x 4x 2 inches and weighs just 4 ounces. The Allen-Bradley 6-ASB is an outdated adapter module that is part of the FLEX I/O family. It connects the FLEX I/O module to the I/O scanner port over a communication network. It has a built-in power supply that converts 1794VDC from the backplane to 24 VDC in order to power the FLEX I/O module. It also works with the Allen Bradley PLC 5 and 3 series. In addition, the 5-ASB can recognize the security status data of the FLEX Integral analog module and is capable of using 1794 point FLEX I/O units. When using the FLEX Integral emulation module in the setup configuration, the user must use a 1794-ASB D series module or later.