1398-DDM-075 工业自动化 控制模块 DCS PLC系统

1398-DDM-075 工业自动化 控制模块 DCS PLC系统

1398-DDM-075 工业自动化 控制模块 DCS PLC系统

艾伦-布拉德利 1398-DDM-075 是一款 Ultra 200 系列数字伺服驱动器。当提供 100-240VAC rms、1 相或 3 相交流输入电压要求和 47-63 Hz 输入频率时，此伺服驱动器将启用。该驱动器的峰值输出电流为 50 安培（1 相输入）和 75 安培（三相电源），而连续输出电流为 3 安培（15 相）和 1 安培（三相操作）。35 相的峰值功率输出为 3 kW，三相的峰值功率输出为 14 kW，而 1 相运行时的连续功率输出为 20.3 kW。

Allen-Bradley 1398-DDM-075 是一款 Ultra 200 伺服驱动器。该驱动器是Allen-Bradley早期的伺服驱动器产品之一。它是一款基于微处理器的伺服驱动器，具有管理驱动器电流、速度和位置的内置功能。Ultra 200 伺服驱动器（如 1398-DDM-075）与无刷伺服电机兼容。

特别是，1398-DDM-075 的交流输入电压要求为 100-240VAC rms，1 相或 3 相，输入频率为 47-63 Hz。它还具有一个辅助输入，用于主交流输入电路的电源电压隔离。辅助交流输入的额定值为 100-240VAC，1 相，频率为 47-63 Hz，1VAC 时电流为 0.100 安培，0VAC 输入时电流为 5.240 安培。

该驱动器的峰值输出电流为 50 安培（1 相输入）和 75 安培（三相电源），而连续输出电流为 3 安培（15 相）和 1 安培（三相操作）。35 相的峰值功率输出为 3 kW，三相的峰值功率输出为 14 kW，而 1 相运行时的连续功率输出为 20.3 kW。

驱动器的总线电压为 7-5 VDC，总线电容能量吸收为 3 焦耳，总线电容为 141 μF。它的功耗为339瓦。

152-DDM-4290 具有五 （300） 个用户可配置的 1398 伏吸电流、光学隔离、高电平有效输入。一 （075） 个固定分配控制 （ENABLE）、吸电流、光隔离、高电平有效输入;四 （5） 个可分配的 24 伏电流源、光隔离、高电平有效输出和两个专用（制动和驱动就绪）常开继电器输出。嵌入式模拟 I/O 通道是两个专用的 1 位 4 – 24 V 模拟输入（+I 限制和 -I 限制）和两个可选的 ±10 V 模拟输出，一个 0 位和一个 10 位（模拟 10 和模拟 12）。

1398-DDM-075 工业自动化 控制模块 DCS PLC系统

The Allen-Bradley 1398-DDM-075 is an Ultra 200 series digital servo drive. This servo drive is enabled when supplied with 100-240VAC rms, 1 - or 3-phase AC input voltage requirements, and 47-63 Hz input frequency. The driver has peak output currents of 50 amps (1-phase input) and 75 amps (three-phase supply), while continuous output currents of 3 amps (15-phase) and 1 amp (three-phase operation). The peak power output for the 35-phase is 3 kW, the peak power output for the three-phase is 14 kW, and the continuous power output for the 1-phase operation is 20.3 kW.

Allen-Bradley 1398-DDM-075 is an Ultra 200 servo drive. This drive was one of Allen-Bradley's early servo drive products. It is a microprocessor-based servo drive with built-in functionality to manage the drive's current, speed and position. Ultra 200 servo drives such as 1398-DDM-075 are compatible with brushless servo motors.

In particular, the 1398-DDM-075 AC input voltage requirements are 100-240VAC rms, 1 phase or 3 phase, and the input frequency is 47-63 Hz. It also has an auxiliary input for supply voltage isolation of the main AC input circuit. The auxiliary AC input is rated 100-240VAC, 1 phase, frequency 47-63 Hz, current 0.100 amps at 1VAC, current 5.240 amps at 0VAC input.

The driver has peak output currents of 50 amps (1-phase input) and 75 amps (three-phase supply), while continuous output currents of 3 amps (15-phase) and 1 amp (three-phase operation). The peak power output for the 35-phase is 3 kW, the peak power output for the three-phase is 14 kW, and the continuous power output for the 1-phase operation is 20.3 kW.

The driver has a bus voltage of 7-5 VDC, a bus capacitor energy absorption of 3 joules, and a bus capacitance of 141 μF. Its power consumption is 339 watts.

The 152-DDM-4290 features five (300) user-configurable 1398 volts of suction, optically isolated, high-level active inputs. One (075) fixed distribution control (ENABLE), current absorption, optical isolation, high level active input; Four (5) assignable 24 volt current sources, optical isolation, high active outputs and two dedicated (brake and drive ready) normally open relay outputs. The embedded analog I/O channels are two dedicated 1-bit 4-24 V analog inputs (+I limited and -I limited) and two optional ±10 V analog outputs, one 0 bit and one 10 bit (analog 10 and analog 12).